777P-PT PulseTech 12V Digital Battery Tester w/ Built-in Printer

777P-PT PulseTech 12V Digital Battery Tester w/ Built-in Printer

390PT PulseTech Battery Analyzer, 6V and 12V Battery Tester

The 390PT Battery and System Analyzer lets you quickly, safely and accurately test both 6-Volt and 12-Volt lead-acid batteries (VRLA, AGM, gel and flooded cell) in or out of the vehicle and test 12-Volt and 24-Volt charging systems for proper operation. Combined singe load, dynamic resistance technology and algorithms display battery voltage and capacity in easy to understand results in seconds. The handy "QUICK START" instruction guide is printed on the back of the analyzer.

NSN: 6130-01-580-3882.

TEST FOR BATTERY AND CHARGING SYSTEM PROBLEMS

An absolute necessity for your battery shop or maintenance bay, the 390PT uses patented single load, dynamic resistance technology to completely analyze your battery and charging system quickly, safely and accurately. You’ll provide better battery maintenance by locating the 6-Volt and 12-Volt vehicle batteries or 12-Volt and 24-Volt starting systems that require attention while still in the vehicle. Find battery issues  before they become problems.

      ·    Tests (VRLA, AGM, gel and flooded cell) – both 6-Volt and 12-Volt batteries
      ·    Determines state of charge, cold cranking amps (CCAs) and good/bad battery
      ·    Tests batteries IN or OUT of the vehicle
      ·    Tests 12-Volt and 24-Volt charging systems for proper operation
      ·    Tests discharged batteries down to 1.5-Volts
      ·    Handy QUICKSTART instruction guide print on the back so you can’t lose it
      ·    Displays battery voltage and battery capacity
      ·    Rugged shock resistant rubber “boot” to protect your investment
      ·    Selects from 6 languages:  English, Spanish, French, German, Italian and Portuguese
      ·    One-Year Limited Warranty

FAST AND EASY TO USE

      1.    Turn off ignition, all accessories and loads.  Close all car doors and trunk.
      2.    Make sure battery terminals are clean.  Attach black lead to negative battery terminal and red lead to positive battery
             terminal.
      3.    Press up or down arrow indicators and press the side arrow enter key to select the battery test, battery type and battery
             rating.
      4.    Battery test results will display one of the following:  GOOD & PASS, GOOD & RECHARGE, RECHARGE & RETEST, BAD&
             REPLACE or BAD CELL & REPLACE
      5.    Press up or down arrow indicators and side-arrow enter key to select system test.
      6.    System test results will display one of the following:  CRANKING VOLTS NORMAL, CRANKING VOLTS LOW or CRANKING
             VOLTS NOT DETECTED
      7.    Subsequent system tests show high, low and normal charging volts at idle and with accessories

For best results when using this battery tester, use female conversion connectors (part number 741X060) on a group 31 battery and male conversion connectors (part number 741X061) on a side-mount battery.

Model Name: 390PT Analyzer 6V & 12V Battery and System Tester
Model Number: 390PT
Part Number: 741X390
NSN: 6130-01-580-3882

Features
•    Tests 12V & 6V lead-acid batteries (VRLA, AGM, gel and flooded cell)
•    12V & 24V electrical system tests
•    Displays battery voltage and battery capacity
•    Determines state of charge, cold cranking amps (CCAs) and good/bad battery
•    Tests batteries IN or OUT of the vehicle
•    Handy QUICKSTART instruction guide printed on the back for easy reference
•    Rugged shock resistant rubber “boot” to protect your investment
•    Tests discharged batteries down to 1.5V, operating from an internal battery  
     Selectable display languages: English, French, Spanish, German, Italian, and Portuguese
    
Electrical Characteristics
    Rating System: SAE, DIN, EN, IEC, JIS Battery No.
    Operation Range: 40 to 2000 CCA (SAE)
    Minimum Battery Voltage for Analysis: 1.5V
    Voltmeter Range: 1.5V to 30V
    Internal Batteries: 1 Each 9 Volt

Display
2 Lines 16 Character LCD Decision Readout of:
        1. Good & Pass
        2. Good & Recharge
        3. Recharge & Retest
        4. Bad & Replace
        5. Bad Cell & Replace
State-of-Charge (SOC) Displayed as a Percentage
State-of-Health (SOH) Displayed as a Percentage

Mechanical / Physical Characteristics
Dimensions: 7.8” L x 4.5” W x 2.1” H (198 mm L x 114 mm W x 53 mm H)
Weight: 1.40 lbs. (0.64 Kg)
Shipping Weight: 1.78 lbs. (0.807 Kg) Each
Battery Cable Length: 2.62’ (80 cm)

Environmental
Operating Temperature: 32º F to 122º F (0º C to 50º C)

Write Your Own Review
You're reviewing:390PT PulseTech Battery Analyzer, 6V and 12V Battery Tester